 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| LM2594 0.5 A, Step-Down Switching Regulator The LM2594 regulator is monolithic integrated circuit ideally suited for easy and convenient design of a step-down switching regulator (buck converter). It is capable of driving a 0.5 A load with excellent line and load regulation. This device is available in adjustable output version. It is internally compensated to minimize the number of external components to simplify the power supply design. Since LM2594 converter is a switch-mode power supply, its efficiency is significantly higher in comparison with popular three-terminal linear regulators, especially with higher input voltages. The LM2594 operates at a switching frequency of 150 kHz thus allowing smaller sized filter components than what would be needed with lower frequency switching regulators. Available in a standard 8-Lead PDIP and 8-Lead Surface Mount packages. The other features include a guaranteed $4% tolerance on output voltage within specified input voltages and output load conditions, and $15% on the oscillator frequency. External shutdown is included, featuring 50 mA (typical) standby current. Self protection features include switch cycle-by-cycle current limit for the output switch, as well as thermal shutdown for complete protection under fault conditions. Features http://onsemi.com MARKING DIAGRAMS 8 1 SOIC-8 D SUFFIX CASE 751 8 LM2594 AYWW G 1 2594-ADJ AWL YYWW PDIP-8 N SUFFIX CASE 626 A WL YY WW G or G = Assembly Location = Wafer Lot = Year = Work Week = Pb-Free Package * * * * * * * * * * * * * * * * Adjustable Output Voltage Range 1.23 V - 37 V Guaranteed 0.5 A Output Load Current Wide Input Voltage Range up to 40 V 150 kHz Fixed Frequency Internal Oscillator TTL Shutdown Capability Low Power Standby Mode, typ 50 mA Thermal Shutdown and Current Limit Protection Internal Loop Compensation Moisture Sensitivity Level (MSL) Equals 1 These are Pb-Free Devices Simple High-Efficiency Step-Down (Buck) Regulator Efficient Pre-Regulator for Linear Regulators On-Card Switching Regulators Positive to Negative Converter (Buck-Boost) Negative Step-Up Converters Power Supply for Battery Chargers PIN CONNECTIONS SOIC-8 NC NC NC FB 1 2 3 4 8 OUTPUT 7 VIN 6 GND 5 ON/OFF Applications NC NC NC FB (Top View) PDIP-8 1 2 3 4 8 7 6 5 OUTPUT VIN GND ON/OFF (Top View) ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 23 of this data sheet. (c) Semiconductor Components Industries, LLC, 2009 January, 2009 - Rev. 0 1 Publication Order Number: LM2594/D LM2594 12 V Unregulated DC Input +VIN LM2594 7 Output 8 CIN = 68 mF 5 ON/OFF 6 GND COUT D1 1N5817 220 mF Feedback 4 L1 100 mH CFF R1 = 1 kW R2 = 3k VOUT = 5 V; Iload = 0.5 A Figure 1. Typical Application 0.5 Figure 2. Representative Block Diagram PIN FUNCTION DESCRIPTION Pin No. 1-3 4 5 Symbol NC FB ON/OFF Not Connected This pin is the direct input of the error amplifier and the resistor network R2, R1 is connected externally to allow programming of the output voltage. Allows the switching regulator circuit to be shut down using logic levels, thus dropping the total input supply current to approximately 50 mA. The threshold voltage is typical. 1.6 V. Applying a voltage above this value (up to VIN) shuts the regulator off. If the voltage applied to this pin is lower than 1.6 V or if this pin is left open, the regulator will be in the "on" condition. Circuit ground pin. See the information about the printed circuit board layout. Positive input supply for LM2594 step-down switching regulator. In order to minimize voltage transients and to supply the switching currents needed by the regulator, a suitable input bypass capacitor must be present (CIN in Figure 1) Emitter of the internal switch. The saturation voltage Vsat of the output switch is typically 1 V. It should be kept in mind that PCB area connected to this pin should be kept to a minimum in order to minimize coupling to sensitive circuitry Description (Refer to Figure 1) 6 7 GND +VIN 8 OUTPUT http://onsemi.com 2 LM2594 MAXIMUM RATINGS Symbol Vin ON/OFF Vout PD RqJA RqJC PD RqJA Tstg - - TJ Maximum Supply Voltage ON/OFF Pin Input Voltage Output Voltage to Ground (Steady-State) Power Dissipation 8-Lead DIP Thermal Resistance, Junction-to-Ambient Thermal Resistance, Junction-to-Case Power Dissipation 8-Lead Surface Mount Thermal Resistance, Junction-to-Ambient Storage Temperature Range Minimum ESD Rating (Human Body Model: C = 100 pF, R = 1.5 kW) Lead Temperature (Soldering, 10 seconds) Maximum Junction Temperature Rating Value 45 -0.3 V V +Vin -1.0 Internally Limited 100 5.0 Internally Limited 175 -65 to +150 2.0 260 150 Unit V V V W C/W C/W W C/W C kV C C Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. OPERATING RATINGS (Operating Ratings indicate conditions for which the device is intended to be functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics table) Symbol TJ VIN Operating Temperature Range Supply Voltage Rating Value -40 to +125 4.5 V to 40 V Unit C V http://onsemi.com 3 LM2594 SYSTEM PARAMETERS ELECTRICAL CHARACTERISTICS Specifications with standard type face are for TJ = 25C, and those with boldface type apply over full Operating Temperature Range -40C to +125C Characteristics LM2594 (Note 1, Test Circuit Figure 16) Feedback Voltage (Vin = 12 V, ILoad = 0.1 A, Vout = 5.0 V, ) Feedback Voltage (8.0 V Vin 40 V, 0.1 A ILoad 0.5 A, Vout = 5.0 V) Efficiency (Vin = 12 V, ILoad = 0.5 A, Vout = 5.0 V) Characteristics Feedback Bias Current (Vout = 5.0 V) Oscillator Frequency (Note 2) Saturation Voltage (Iout = 0.5 A, Notes 3 and 4) Max Duty Cycle "ON" (Note 4) Current Limit (Peak Current, Notes 3 and 4) Output Leakage Current (Notes 5 and 6) Output = 0 V Output = -1.0 V Quiescent Current (Note 5) Standby Quiescent Current (ON/OFF Pin = 5.0 V ("OFF")) (Note 6) ON/OFF PIN LOGIC INPUT Threshold Voltage Vout = 0 V (Regulator OFF) Vout = Nominal Output Voltage (Regulator ON) ON/OFF Pin Input Current ON/OFF Pin = 5.0 V (Regulator OFF) ON/OFF Pin = 0 V (regulator ON) IIH IIL - - 15 0.01 30 5.0 mA mA VIH VIL 2.2 2.4 1.0 0.8 1.6 V V V VFB_nom VFB Symbol Ib fosc Vsat DC ICL IL 0.7 0.65 135 120 1.193 1.18 - Min 80 Typ 25 150 1.0 95 1.0 1.6 1.8 2.0 30 10 200 250 Max 100 200 165 180 1.2 1.4 1.23 1.267 1.28 V V % Unit nA kHz V % A mA Symbol Min Typ Max Unit 0.5 13 5.0 50 IQ Istby mA mA 1. External components such as the catch diode, inductor, input and output capacitors can affect switching regulator system performance. When the LM2594 is used as shown in the Figure 16 test circuit, system performance will be as shown in system parameters section. 2. The oscillator frequency reduces to approximately 30 kHz in the event of an output short or an overload which causes the regulated output voltage to drop approximately 40% from the nominal output voltage. This self protection feature lowers the average dissipation of the IC by lowering the minimum duty cycle from 5% down to approximately 2%. 3. No diode, inductor or capacitor connected to output (Pin 8) sourcing the current. 4. Feedback (Pin 4) removed from output and connected to 0 V. 5. Feedback (Pin 4) removed from output and connected to +12 V to force the output transistor "off". 6. Vin = 40 V. http://onsemi.com 4 LM2594 TYPICAL PERFORMANCE CHARACTERISTICS (Circuit of Figure 16) 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 -0.2 -0.4 -0.6 0 5.0 10 15 20 25 30 35 40 Vout = 5 V Vout, OUTPUT VOLTAGE CHANGE (%) 1.0 Vout , OUTPUT VOLTAGE CHANGE (%) 0.8 0.6 0.4 0.2 0 -0.2 -0.4 -0.6 -0.8 -1.0 -50 -25 0 25 50 75 100 125 Vin = 20 V ILoad = 100 mA Normalized at TJ = 25C ILoad = 100 mA TJ = 25C TJ, JUNCTION TEMPERATURE (C) Vin, INPUT VOLTAGE (V) Figure 3. Normalized Output Voltage Figure 4. Line Regulation 2.0 INPUT - OUTPUT DIFFERENTIAL (V) I O, OUTPUT CURRENT (A) 1.3 1.2 1.1 1.0 0.9 0.8 0.7 125 0.6 -50 -25 0 25 60 75 Vin = 12 V 1.5 ILoad = 500 mA 1.0 ILoad = 100 mA 0.5 L = 100 mH R_ind = 30 mW 0 -50 -25 0 25 60 75 100 100 125 TJ, JUNCTION TEMPERATURE (C) TJ, JUNCTION TEMPERATURE (C) Figure 5. Dropout Voltage 12 I Q, QUIESCENT CURRENT (mA) 11 10 9 8 7 6 5 4 0 5 10 15 20 25 30 35 40 ILoad = 100 mA 160 I stby , STANDBY QUIESCENT CURRENT ( A) 140 120 100 80 60 40 20 0 -50 -25 Figure 6. Current Limit Vout = 5 V Measured at GND Pin TJ = 25C ILoad = 500 mA VON/OFF = 5.0 V Vin = 40 V Vin = 12 V 0 25 60 75 100 125 Vin, INPUT VOLTAGE (V) TJ, JUNCTION TEMPERATURE (C) Figure 7. Quiescent Current Figure 8. Standby Quiescent Current http://onsemi.com 5 LM2594 TYPICAL PERFORMANCE CHARACTERISTICS (Circuit of Figure 16) 1.3 Vsat , SATURATION VOLTAGE (V) NORMALIZED FREQUENCY (%) 1.2 1.1 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0 0.1 0.2 0.3 0.4 0.5 125C -40C 25C 1.0 0.0 -1.0 -2.0 -3.0 -4.0 -5.0 -6.0 -7.0 -8.0 -9.0 -50 -25 0 25 50 75 100 125 SWITCH CURRENT (A) TJ, JUNCTION TEMPERATURE (C) Figure 9. Switch Saturation Voltage Figure 10. Switching Frequency 5.0 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 -50 -25 0 25 50 75 100 125 Vout ' 1.23 V ILoad = 100 mA Ib , FEEDBACK PIN CURRENT (nA) 4.5 V in , INPUT VOLTAGE (V) 100 80 60 40 20 0 -20 -40 -60 -80 -100 -50 -25 0 25 50 75 100 125 TJ, JUNCTION TEMPERATURE (C) TJ, JUNCTION TEMPERATURE (C) Figure 11. Minimum Supply Operating Voltage Figure 12. Feedback Pin Current 95 90 EFFICIENCY (%) 85 80 75 3.3 V, 500 mA 70 0 5 10 15 20 25 30 35 40 45 5 V, 500 mA 12 V, 500 mA VIN, INPUT VOLTAGE (V) Figure 13. Efficiency http://onsemi.com 6 LM2594 TYPICAL PERFORMANCE CHARACTERISTICS (Circuit of Figure 16) A 10 V 0 0.8 A B 0.4 A 0 0.8 A C D 0.4 A 0 2 ms/div Load Current 0.1 A 0 100 ms/div 0.5 A 100 mV Output 0 Voltage Change - 100 mV Figure 14. Switching Waveforms Vout = 5 V A: Output Pin Voltage, 10 V/div B: Switch Current, 0.4 A/div C: Inductor Current, 0.4 A/div, AC-Coupled D: Output Ripple Voltage, 50 mV/div, AC-Coupled Horizontal Time Base: 2.0 ms/div Figure 15. Load Transient Response Adjustable Output Voltage Versions Feedback Vin 7 6 8.5 V - 40 V Unregulated DC Input Cin 100 mF GND 5 LM2594 4 Output 8 ON/OFF D1 1N5822 Cout 220 mF R2 Load R1 L1 100 mH Vout 5.0 V/0.5 A CFF V out + V R2 + R1 ref 1.0 ) R2 R1 1.0 V out V ref Where Vref = 1.23 V, R1 between 1.0 k and 5.0 k Figure 16. Typical Test Circuit http://onsemi.com 7 LM2594 PCB LAYOUT GUIDELINES As in any switching regulator, the layout of the printed On the other hand, the PCB area connected to the Pin 2 circuit board is very important. Rapidly switching currents (emitter of the internal switch) of the LM2594 should be associated with wiring inductance, stray capacitance and kept to a minimum in order to minimize coupling to sensitive parasitic inductance of the printed circuit board traces can circuitry. generate voltage transients which can generate Another sensitive part of the circuit is the feedback. It is electromagnetic interferences (EMI) and affect the desired important to keep the sensitive feedback wiring short. To operation. As indicated in the Figure 16, to minimize assure this, physically locate the programming resistors near inductance and ground loops, the length of the leads to the regulator, when using the adjustable version of the indicated by heavy lines should be kept as short as possible. LM2594 regulator. For best results, single-point grounding (as indicated) or ground plane construction should be used. DESIGN PROCEDURE Buck Converter Basics The LM2594 is a "Buck" or Step-Down Converter which is the most elementary forward-mode converter. Its basic schematic can be seen in Figure 17. The operation of this regulator topology has two distinct time periods. The first one occurs when the series switch is on, the input voltage is connected to the input of the inductor. The output of the inductor is the output voltage, and the rectifier (or catch diode) is reverse biased. During this period, since there is a constant voltage source connected across the inductor, the inductor current begins to linearly ramp upwards, as described by the following equation: I L(on) + V IN * V OUT ton L This period ends when the power switch is once again turned on. Regulation of the converter is accomplished by varying the duty cycle of the power switch. It is possible to describe the duty cycle as follows: t d + on , where T is the period of switching. T For the buck converter with ideal components, the duty cycle can also be described as: V d + out V in Figure 18 shows the buck converter, idealized waveforms of the catch diode voltage and the inductor current. Von(SW) Diode Voltage During this "on" period, energy is stored within the core material in the form of magnetic flux. If the inductor is properly designed, there is sufficient energy stored to carry the requirements of the load during the "off" period. Power Switch L Power Switch Off VD(FWD) Power Switch On Power Switch Off Power Switch On Vin D Cout RLoad Time Figure 17. Basic Buck Converter Ipk Inductor Current ILoad(AV) Imin Diode Power Switch Power Switch Time The next period is the "off" period of the power switch. When the power switch turns off, the voltage across the inductor reverses its polarity and is clamped at one diode voltage drop below ground by the catch diode. The current now flows through the catch diode thus maintaining the load current loop. This removes the stored energy from the inductor. The inductor current during this time is: I L(off) + V OUT * V D toff L Diode Figure 18. Buck Converter Idealized Waveforms http://onsemi.com 8 LM2594 PROCEDURE (ADJUSTABLE OUTPUT VERSION: LM2594) Procedure Given Parameters: Vout = Regulated Output Voltage Vin(max) = Maximum DC Input Voltage ILoad(max) = Maximum Load Current 1. Programming Output Voltage To select the right programming resistor R1 and R2 value (see Figure 1) use the following formula: R2 V out + V 1.0 ) ref R1 where Vref = 1.23 V R2 + R1 Given Parameters: Vout = 5.0 V Vin(max) = 12 V ILoad(max) = 0.5 A 1. Programming Output Voltage (selecting R1 and R2) Select R1 and R2: V out + 1.23 1.0 ) V out V ref R2 R1 Select R1 = 1.0 kW + 5V * 1.0 1.23 V Example Resistor R1 can be between 1.0 k and 5.0 kW. (For best temperature coefficient and stability with time, use 1% metal film resistors). * 1.0 R2 + R1 V out Vref R2 = 3.0 kW, choose a 3.0k metal film resistor. * 1.0 2. Input Capacitor Selection (Cin) A 68 mF, 50 V aluminium electrolytic capacitor located near the input and ground pin provides sufficient bypassing. 2. Input Capacitor Selection (Cin) To prevent large voltage transients from appearing at the input and for stable operation of the converter, an aluminium or tantalum electrolytic bypass capacitor is needed between the input pin +Vin and ground pin GND This capacitor should be located close to the IC using short leads. This capacitor should have a low ESR (Equivalent Series Resistance) value. For additional information see input capacitor section in the "Application Information" section of this data sheet. 3. Catch Diode Selection (D1) A. Since the diode maximum peak current exceeds the regulator maximum load current the catch diode current rating must be at least 1.2 times greater than the maximum load current. For a robust design, the diode should have a current rating equal to the maximum current limit of the LM2594 to be able to withstand a continuous output short. B. The reverse voltage rating of the diode should be at least 1.25 times the maximum input voltage. 3. Catch Diode Selection (D1) A. For this example, a 1.0 A current rating is adequate. B. For Vin = 12 V use a 20 V 1N5817 Schottky diode or any suggested fast recovery diode in the Table 2. http://onsemi.com 9 LM2594 PROCEDURE (ADJUSTABLE OUTPUT VERSION: LM2594) (CONTINUED) Procedure 4. Inductor Selection (L1) A. Use the following formula to calculate the inductor Volt x microsecond [V x ms] constant: V E T+ V Example 4. Inductor Selection (L1) A. Calculate E x T [V x ms] constant: E ms IN *V OUT *V OUT )V D D 1000 150 kHz T + 12 * 5 * 1.0 T+ 6 5.5 11.5 5 ) 0.5 12 * 1 ) 0.5 ms 1000 150 kHz V ms SAT V IN *V SAT )V V E 6.7 V B. Match the calculated E x T value with the corresponding number on the vertical axis of the Inductor Value Selection Guide shown in Figure 19. This E x T constant is a measure of the energy handling capability of an inductor and is dependent upon the type of core, the core area, the number of turns, and the duty cycle. C. Next step is to identify the inductance region intersected by the E x T value and the maximum load current value on the horizontal axis shown in Figure 19. D. Select an appropriate inductor from Table 3. The inductor chosen must be rated for a switching frequency of 150 kHz and for a current rating of 1.15 x ILoad. The inductor current rating can also be determined by calculating the inductor peak current: V I +I B. E x T = 19.2 [V x ms] C. ILoad(max) = 0.5 A Inductance Region = L20 D. Proper inductor value = 100 mH Choose the inductor from Table 3. p(max) Load(max) 2L where ton is the "on" time of the power switch and V t on + out x 1.0 V f osc in 5. Output Capacitor Selection (Cout) A. Since the LM2594 is a forward-mode switching regulator with voltage mode control, its open loop has 2-pole-1-zero frequency characteristic. The loop stability is determined by the output capacitor (capacitance, ESR) and inductance values. For stable operation use recommended values of the output capacitors in Table 1. Low ESR electrolytic capacitors between 180 mF and 1000 mF provide best results. B. The capacitors voltage rating should be at least 1.5 times greater than the output voltage, and often much higher voltage rating is needed to satisfy low ESR requirement 6. Feedforward Capacitor (CFF) It provides additional stability mainly for higher input voltages. For Cff selection use Table 1. The compensation capacitor between 0.6 nF and 15 nF is wired in parallel with the output voltage setting resistor R2, The capacitor type can be ceramic, plastic, etc.. 6. Feedforward Capacitor (CFF) In this example is recommended feedforward capacitor 1.5 nF. 5. Output Capacitor Selection (Cout) A. In this example is recommended Nichicon PM capacitors: 220 mF/25 V ) in * V out ton http://onsemi.com 10 LM2594 LM2594 Series Buck Regulator Design Procedures (continued) Table 1. RECOMMENDED VALUES OF THE OUTPUT CAPACITOR AND FEEDFORWARD CAPACITOR (Iload = 0.5 A) Nichicon Pm Capacitors Vin (V) 40 35 26 20 18 12 10 Vout (V) CFF (nF) 1000/10/ 60 1000/10/ 60 1000/10/ 60 1000/10/ 60 1000/10/ 60 470/10/ 140 470/10/ 140 2 15 680/250 680/150 470/10/ 140 470/10/ 140 470/10/ 140 470/10/ 140 470/10/ 140 3 4.7 470/10/ 140 470/10/ 140 330/10/ 160 220/25/ 110 220/25/ 110 220/25/ 110 220/25/ 110 4 1.5 Capacity/Voltage Range / ESR[mF/V/mW] 470/10/ 140 330/10/ 160 220/25/ 110 220/25/ 110 220/25/ 110 180/25/ 140 180/25/ 140 6 1.5 9 1.5 12 1.5 15 1 24 0.6 28 0.6 330/10/ 160 180/25/ 140 180/25/ 140 100/25/ 240 100/25/ 240 100/25/ 240 220/25/ 110 180/25/ 140 180/25/ 140 100/25/ 240 100/25/ 240 220/110 180/25/ 140 100/25/ 240 100/25/ 240 100/25/ 240 180/25/ 140 180/25/ 140 180/25/ 140 180/35/ 100 180/35/ 100 E*T(V*us) 0.1 0.2 Maximum load current (A) 0.3 0.4 0.5 Figure 19. Inductor Value Selection Guides (For Continuous Mode Operation) http://onsemi.com 11 LM2594 Table 2. DIODE SELECTION 1A Diodes Surface Mouns VR 20 V 30 V 40 V 50 V or more Schottky MBRS140 10BQ040 10MQ040 MBRS160 10BQ050 10MQ060 MBRS1100 10MQ090 SGL41-60 SS16 MBRS140 10BQ040 Ultra Fast Recovery All of these diodes are rated to at least 60 V. MURS120 10BF10 Schottky 1N5817 SR102 1N5818 SR103 11DQ03 1N5819 SR104 11DQ04 SR105 MBR150 11DQ05 MBR160 Through Hole Ultra Fast Recovery All of these diodes are rated to at least 60 V. MUR120 HER101 11DF1 http://onsemi.com 12 LM2594 Table 3. INDUCTOR MANUFACTURERS PART NUMBERS Schott Inductance (mH) L1 L2 L3 L4 L5 L6 L7 L8 L9 L10 L11 L12 L13 L14 L15 L16 L17 L18 L19 L20 L21 L26 L27 220 150 100 68 47 33 22 330 220 150 100 68 47 33 22 15 330 220 150 100 68 330 220 Current (A) 0.18 0.21 0.26 0.32 0.37 0.44 0.60 0.26 0.32 0.39 0.48 0.58 0.70 0.83 0.99 1.24 0.42 0.55 0.66 0.82 0.99 0.80 1.00 Through Hole 67143910 67143920 67143930 67143940 67148310 67148320 67148330 67143950 67143960 67143970 67143980 67143990 67144000 67148340 67148350 67148360 67144030 67144040 67144050 67144060 67144070 67144100 67144110 Surface Mount 67144280 67144290 67144300 67144310 67148420 67148430 67148440 67144320 67144330 67144340 67144350 67144360 67144380 67148450 67148460 67148470 67144410 67144420 67144430 67144440 67144450 67144480 67144490 Renco Through Hole RL-5470-3 RL-5470-4 RL-5470-5 RL-1284-68 RL-1284-47 RL-1284-33 RL-1284-22 RL-5470-2 RL-5470-3 RL-5470-4 RL-5470-5 RL-5470-6 RL-5470-7 RL-1284-33 RL-1284-22 RL-1284-15 RL-5471-1 RL-5471-2 RL-5471-3 RL-5471-4 RL-5471-5 RL-5471-1 RL-5471-2 Surface Mount PE-53801 PE-53802 PE-53803 PE-53804 PE-53805 PE-53806 PE-53807 PE-53808 PE-53809 PE-53810 PE-53811 PE-53812 PE-53813 PE-53814 PE-53815 PE-53816 PE-53817 PE-53818 PE-53819 PE-53820 PE-53821 PE-53826 PE-53827 Pulse Engineering Through Hole PE-53801-S PE-53802-S PE-53803-S PE-53804-S PE-53805-S PE-53806-S PE-53807-S PE-53808-S PE-53809-S PE-53810-S PE-53811-S PE-53812-S PE-53813-S PE-53814-S PE-53815-S PE-53816-S PE-53817-S PE-53818-S PE-53819-S PE-53820-S PE-53821-S PE-53826-S PE-53827-S Surface Mount - - - - - - - - - - - - - - - - - - RFB0810-151L RFB0810-101L RFB0810-680L - - Coilcraft Surface Mount DO1608-224 DO1608-154 DO1608-104 DO1608-68 DO1608-473 DO1608-333 DO1608-223 DO3308-334 DO3308-224 DO3308-154 DO3308-104 DO1608-683 DO3308-473 DO1608-333 DO1608-223 DO1608-153 DO3316-334 DO3316-224 DO3316-154 DO3340P-104 DDO3316-683 - - http://onsemi.com 13 LM2594 APPLICATION INFORMATION EXTERNAL COMPONENTS Input Capacitor (Cin) The Input Capacitor Should Have a Low ESR For stable operation of the switch mode converter a low ESR (Equivalent Series Resistance) aluminium or solid tantalum bypass capacitor is needed between the input pin and the ground pin, to prevent large voltage transients from appearing at the input. It must be located near the regulator and use short leads. With most electrolytic capacitors, the capacitance value decreases and the ESR increases with lower temperatures. For reliable operation in temperatures below -25C larger values of the input capacitor may be needed. Also paralleling a ceramic or solid tantalum capacitor will increase the regulator stability at cold temperatures. The important parameter of the input capacitor is the RMS current rating. Capacitors that are physically large and have large surface area will typically have higher RMS current ratings. For a given capacitor value, a higher voltage electrolytic capacitor will be physically larger than a lower voltage capacitor, and thus be able to dissipate more heat to the surrounding air, and therefore will have a higher RMS current rating. The consequence of operating an electrolytic capacitor beyond the RMS current rating is a shortened operating life. In order to assure maximum capacitor operating lifetime, the capacitor's RMS ripple current rating should be: Irms > 1.2 x d x ILoad RMS Current Rating of Cin regulator loop stability. The ESR of the output capacitor and the peak-to-peak value of the inductor ripple current are the main factors contributing to the output ripple voltage value. Standard aluminium electrolytics could be adequate for some applications but for quality design, low ESR types are recommended. An aluminium electrolytic capacitor's ESR value is related to many factors such as the capacitance value, the voltage rating, the physical size and the type of construction. In most cases, the higher voltage electrolytic capacitors have lower ESR value. Often capacitors with much higher voltage ratings may be needed to provide low ESR values that, are required for low output ripple voltage. Feedfoward Capacitor (Adjustable Output Voltage Version) This capacitor adds lead compensation to the feedback loop and increases the phase margin for better loop stability. For CFF selection, see the design procedure section. The Output Capacitor Requires an ESR Value That Has an Upper and Lower Limit As mentioned above, a low ESR value is needed for low output ripple voltage, typically 1% to 2% of the output voltage. But if the selected capacitor's ESR is extremely low (below 0.05 W), there is a possibility of an unstable feedback loop, resulting in oscillation at the output. This situation can occur when a tantalum capacitor, that can have a very low ESR, is used as the only output capacitor. At Low Temperatures, Put in Parallel Aluminium Electrolytic Capacitors with Tantalum Capacitors where d is the duty cycle, for a buck regulator V t d + on + out T V in |V out| t on and d + + for a buck boost regulator. * T |V out| ) V in Output Capacitor (Cout) For low output ripple voltage and good stability, low ESR output capacitors are recommended. An output capacitor has two main functions: it filters the output and provides Electrolytic capacitors are not recommended for temperatures below -25C. The ESR rises dramatically at cold temperatures and typically rises 3 times at -25C and as much as 10 times at -40C. Solid tantalum capacitors have much better ESR spec at cold temperatures and are recommended for temperatures below -25C. They can be also used in parallel with aluminium electrolytics. The value of the tantalum capacitor should be about 10% or 20% of the total capacitance. The output capacitor should have at least 50% higher RMS ripple current rating at 150 kHz than the peak-to-peak inductor ripple current. http://onsemi.com 14 LM2594 Catch Diode Locate the Catch Diode Close to the LM2594 The LM2594 is a step-down buck converter; it requires a fast diode to provide a return path for the inductor current when the switch turns off. This diode must be located close to the LM2594 using short leads and short printed circuit traces to avoid EMI problems. Use a Schottky or a Soft Switching Ultra-Fast Recovery Diode Inductor 0.4 A Inductor Current Waveform 0 A 0.8 A Power Switch Current Waveform 0 A The magnetic components are the cornerstone of all switching power supply designs. The style of the core and the winding technique used in the magnetic component's design has a great influence on the reliability of the overall power supply. Using an improper or poorly designed inductor can cause high voltage spikes generated by the rate of transitions in current within the switching power supply, and the possibility of core saturation can arise during an abnormal operational mode. Voltage spikes can cause the semiconductors to enter avalanche breakdown and the part can instantly fail if enough energy is applied. It can also cause significant RFI (Radio Frequency Interference) and EMI (Electro-Magnetic Interference) problems. Continuous and Discontinuous Mode of Operation HORIZONTAL TIME BASE: 2.0 ms/DIV Figure 20. Continuous Mode Switching Current Waveforms Selecting the Right Inductor Style The LM2594 step-down converter can operate in both the continuous and the discontinuous modes of operation. The regulator works in the continuous mode when loads are relatively heavy, the current flows through the inductor continuously and never falls to zero. Under light load conditions, the circuit will be forced to the discontinuous mode when inductor current falls to zero for certain period of time (see Figure 20 and Figure 21). Each mode has distinctively different operating characteristics, which can affect the regulator performance and requirements. In many cases the preferred mode of operation is the continuous mode. It offers greater output power, lower peak currents in the switch, inductor and diode, and can have a lower output Some important considerations when selecting a core type are core material, cost, the output power of the power supply, the physical volume the inductor must fit within, and the amount of EMI (Electro-Magnetic Interference) shielding that the core must provide. The inductor selection guide covers different styles of inductors, such as pot core, E-core, toroid and bobbin core, as well as different core materials such as ferrites and powdered iron from different manufacturers. For high quality design regulators the toroid core seems to be the best choice. Since the magnetic flux is contained within the core, it generates less EMI, reducing noise problems in sensitive circuits. The least expensive is the bobbin core type, which consists of wire wound on a ferrite rod core. This type of inductor generates more EMI due to the fact that its core is open, and the magnetic flux is not contained within the core. When multiple switching regulators are located on the same printed circuit board, open core magnetics can cause http://onsemi.com 15 VERTRICAL RESOLUTION 1.0 A/DIV Since the rectifier diodes are very significant sources of losses within switching power supplies, choosing the rectifier that best fits into the converter design is an important process. Schottky diodes provide the best performance because of their fast switching speed and low forward voltage drop. They provide the best efficiency especially in low output voltage applications (5.0 V and lower). Another choice could be Fast-Recovery, or Ultra-Fast Recovery diodes. It has to be noted, that some types of these diodes with an abrupt turnoff characteristic may cause instability or EMI troubles. A fast-recovery diode with soft recovery characteristics can better fulfill some quality, low noise design requirements. Table 2 provides a list of suitable diodes for the LM2594 regulator. Standard 50/60 Hz rectifier diodes, such as the 1N4001 series or 1N5400 series are NOT suitable. ripple voltage. On the other hand it does require larger inductor values to keep the inductor current flowing continuously, especially at low output load currents and/or high input voltages. To simplify the inductor selection process, an inductor selection guide for the LM2594 regulator was added to this data sheet (Figure 19). This guide assumes that the regulator is operating in the continuous mode, and selects an inductor that will allow a peak-to-peak inductor ripple current to be a certain percentage of the maximum design load current. This percentage is allowed to change as different design load currents are selected. For light loads (less than approximately 300 mA) it may be desirable to operate the regulator in the discontinuous mode, because the inductor value and size can be kept relatively low. Consequently, the percentage of inductor peak-to-peak current increases. This discontinuous mode of operation is perfectly acceptable for this type of switching converter. Any buck regulator will be forced to enter discontinuous mode if the load current is light enough. LM2594 interference between two or more of the regulator circuits, especially at high currents due to mutual coupling. A toroid, pot core or E-core (closed magnetic structure) should be used in such applications. Do Not Operate an Inductor Beyond its Maximum Rated Current inductor and/or the LM2594. Different inductor types have different saturation characteristics, and this should be kept in mind when selecting an inductor. Exceeding an inductor's maximum current rating may cause the inductor to overheat because of the copper wire losses, or the core may saturate. Core saturation occurs when the flux density is too high and consequently the cross sectional area of the core can no longer support additional lines of magnetic flux. This causes the permeability of the core to drop, the inductance value decreases rapidly and the inductor begins to look mainly resistive. It has only the DC resistance of the winding. This can cause the switch current to rise very rapidly and force the LM2594 internal switch into cycle-by-cycle current limit, thus reducing the DC output load current. This can also result in overheating of the 0.05 A Inductor Current Waveform 0A 0.05 A Power Switch Current Waveform 0A HORIZONTAL TIME BASE: 2.0 ms/DIV Figure 21. Discontinuous Mode Switching Current Waveforms GENERAL RECOMMENDATIONS Output Voltage Ripple and Transients Source of the Output Ripple Minimizing the Output Ripple Since the LM2594 is a switch mode power supply regulator, its output voltage, if left unfiltered, will contain a sawtooth ripple voltage at the switching frequency. The output ripple voltage value ranges from 0.5% to 3% of the output voltage. It is caused mainly by the inductor sawtooth ripple current multiplied by the ESR of the output capacitor. Short Voltage Spikes and How to Reduce Them The regulator output voltage may also contain short voltage spikes at the peaks of the sawtooth waveform (see Figure 22). These voltage spikes are present because of the fast switching action of the output switch, and the parasitic inductance of the output filter capacitor. There are some other important factors such as wiring inductance, stray capacitance, as well as the scope probe used to evaluate these transients, all these contribute to the amplitude of these spikes. To minimize these voltage spikes, low inductance capacitors should be used, and their lead lengths must be kept short. The importance of quality printed circuit board layout design should also be highlighted. Voltage spikes caused by switching action of the output switch and the parasitic inductance of the output capacitor In order to minimize the output ripple voltage it is possible to enlarge the inductance value of the inductor L1 and/or to use a larger value output capacitor. There is also another way to smooth the output by means of an additional LC filter (3 mH, 100 mF), that can be added to the output (see Figure 31) to further reduce the amount of output ripple and transients. With such a filter it is possible to reduce the output ripple voltage transients 10 times or more. Figure 22 shows the difference between filtered and unfiltered output waveforms of the regulator shown in Figure 31. The lower waveform is from the normal unfiltered output of the converter, while the upper waveform shows the output ripple voltage filtered by an additional LC filter. Heatsinking and Thermal Considerations Filtered Output Voltage Unfiltered Output Voltage HORIZONTAL TIME BASE: 5.0 ms/DIV Figure 22. Output Ripple Voltage Waveforms The LM2574 is available in both 8-pin DIP and SOIC-8 packages. When used in the typical application the copper lead frame conducts the majority of the heat from the die, through the leads, to the printed circuit copper. The copper and the board are the heatsink for this package and the other heat producing components, such as the catch diode and inductor. For the best thermal performance, wide copper traces should be used and all ground and unused pins should be soldered to generous amounts of printed circuit board copper, such as a ground plane. Large areas of copper provide the best transfer of heat to the surrounding air. One exception to this is the output (switch) pin, which should not have large areas of copper in order to minimize coupling to sensitive circuitry. Additional improvement in heat dissipation can be achieved even by using of double sided or multilayer boards which can provide even better heat path to the ambient. Using a socket for the 8-pin DIP package is not recommended because socket represents an additional thermal resistance, and as a result the junction temperature will be higher. VERTRICAL RESOLUTION 20 mV/DIV http://onsemi.com 16 VERTICAL RESOLUTION 200 mA/DIV LM2594 Since the current rating of the LM2594 is only 0.5 A, the total package power dissipation for this switcher is quite low, ranging from approximately 0.1 W up to 0.75 W under varying conditions. In a carefully engineered printed circuit board, the through-hole DIP package can easily dissipate up to 0.75 W, even at ambient temperatures of 60C, and still keep the maximum junction temperature below 125C. Thermal Analysis and Design The following formula is to calculate the approximate total power dissipated by the LM2594: PD = (Vin x IQ) + d x ILoad x Vsat where d is the duty cycle and for buck converter V t d + on + O , T V in The following procedure must be performed to determine the operating junction temperature. First determine: 1. PD(max) maximum regulator power dissipation in the application. 2. TA(max) maximum ambient temperature in the application. 3. TJ(max) maximum allowed junction temperature (125C for the LM2594). For a conservative design, the maximum junction temperature should not exceed 110C to assure safe operation. For every additional +10C temperature rise that the junction must withstand, the estimated operating lifetime of the component is halved. 4. RqJC package thermal resistance junction-case. 5. RqJA package thermal resistance junction-ambient. (Refer to Maximum Ratings on page 3 of this data sheet or RqJC and RqJA values). IQ (quiescent current) and Vsat can be found in the LM2594 data sheet, Vin is minimum input voltage applied, VO is the regulator output voltage, ILoad is the load current. The dynamic switching losses during turn-on and turn-off can be neglected if proper type catch diode is used. The junction temperature can be determined by the following expression: TJ = (RqJA) (PD) + TA where (RqJA)(PD) represents the junction temperature rise caused by the dissipated power and TA is the maximum ambient temperature. Some Aspects That can Influence Thermal Design It should be noted that the package thermal resistance and the junction temperature rise numbers are all approximate, and there are many factors that will affect these numbers, such as PC board size, shape, thickness, physical position, location, board temperature, as well as whether the surrounding air is moving or still. Other factors are trace width, total printed circuit copper area, copper thickness, single- or double-sided, multilayer board, the amount of solder on the board or even color of the traces. The size, quantity and spacing of other components on the board can also influence its effectiveness to dissipate the heat. Feedback R4 12 to 25 V Unregulated DC Input +Vin LM2594 L1 100 mH CFF Cin 100 mF/50 V ON/OFF GND D1 1N5819 Cout 220 mF R3 -12 V @ 0.7 A Regulated Output Figure 23. Inverting Buck-Boost Develops -12 V ADDITIONAL APPLICATIONS Inverting Regulator An inverting buck-boost regulator using the LM2594-ADJ is shown in Figure 23. This circuit converts a positive input voltage to a negative output voltage with a common ground by bootstrapping the regulators ground to the negative output voltage. By grounding the feedback pin, the regulator senses the inverted output voltage and regulates it. In this example the LM2594 is used to generate a -12 V output. The maximum input voltage in this case cannot exceed +28 V because the maximum voltage appearing http://onsemi.com 17 LM2594 across the regulator is the absolute sum of the input and output voltages and this must be limited to a maximum of 40 V. This circuit configuration is able to deliver approximately 0.25 A to the output when the input voltage is 12 V or higher. At lighter loads the minimum input voltage required drops to approximately 4.7 V, because the buck-boost regulator topology can produce an output voltage that, in its absolute value, is either greater or less than the input voltage. Since the switch currents in this buck-boost configuration are higher than in the standard buck converter topology, the available output current is lower. This type of buck-boost inverting regulator can also require a larger amount of startup input current, even for light loads. This may overload an input power source with a current limit less than 1.0 A. Such an amount of input startup current is needed for at least 2.0 ms or more. The actual time depends on the output voltage and size of the output capacitor. Because of the relatively high startup currents required by this inverting regulator topology, the use of a delayed startup or an undervoltage lockout circuit is recommended. Using a delayed startup arrangement, the input capacitor can charge up to a higher voltage before the switch-mode regulator begins to operate. The high input current needed for startup is now partially supplied by the input capacitor Cin. It has been already mentioned above, that in some situations, the delayed startup or the undervoltage lockout 12 to 40 V Unregulated DC Input features could be very useful. A delayed startup circuit applied to a buck-boost converter is shown in Figure 28. Figure 30 in the "Undervoltage Lockout" section describes an undervoltage lockout feature for the same converter topology. Design Recommendations: The inverting regulator operates in a different manner than the buck converter and so a different design procedure has to be used to select the inductor L1 or the output capacitor Cout. The output capacitor values must be larger than what is normally required for buck converter designs. Low input voltages or high output currents require a large value output capacitor (in the range of thousands of mF). The recommended range of inductor values for the inverting converter design is between 68 mH and 220 mH. To select an inductor with an appropriate current rating, the inductor peak current has to be calculated. The following formula is used to obtain the peak inductor current: I (V ) |V |) O ) V in x t on [ Load in 2L 1 V in |V | O where t on + x 1.0 , and f osc + 52 kHz. V ) |V | fosc in O I peak Under normal continuous inductor current operating conditions, the worst case occurs when Vin is minimal. Feedback +Vin LM2594 L1 100 mH R4 Cin 100 mF/50 V C1 0.1 mF CFF ON/OFF R2 47k GND D1 1N5819 Cout 220 mF R3 -12 V @ 0.25 A Regulated Output Figure 24. Inverting Buck-Boost Develops with Delayed Startup http://onsemi.com 18 LM2594 +V +Vin +Vin 7 Cin R1 100 mF 47 k LM2594 0 On R2 5.6 k 5 ON/OFF 6 GN D +Vin Cin 100 mF R2 47 k -Vout MOC8101 NOTE: This picture does not show the complete circuit. R1 12 k Q1 2N3906 5 +Vin 7 LM2594 Off Shutdown Input 5.0 V 0 On Shutdown Input Off R3 470 ON/OFF 6 GN D -Vout NOTE: This picture does not show the complete circuit. Figure 25. Inverting Buck-Boost Regulator Shutdown Circuit Using an Optocoupler Figure 26. Inverting Buck-Boost Regulator Shutdown Circuit Using a PNP Transistor Negative Boost Regulator With the inverting configuration, the use of the ON/OFF pin requires some level shifting techniques. This is caused by the fact, that the ground pin of the converter IC is no longer at ground. Now, the ON/OFF pin threshold voltage (1.3 V approximately) has to be related to the negative output voltage level. There are many different possible shut down methods, two of them are shown in Figures 25 and 26. This example is a variation of the buck-boost topology and it is called negative boost regulator. This regulator experiences relatively high switch current, especially at low input voltages. The internal switch current limiting results in lower output load current capability. The circuit in Figure 27 shows the negative boost configuration. The input voltage in this application ranges from -5.0 V to -12 V and provides a regulated -12 V output. If the input voltage is greater than -12 V, the output will rise above -12 V accordingly, but will not damage the regulator. R4 Feedback +Vin Cin 100 mF/ 50 V LM2594 Cout 470 mF ON/OFF GND D1 1N5822 R3 -12 V @ 0.25 A Regulated Output -12 V Unregulated DC Input L1 100 mH Figure 27. Negative Boost Regulator Design Recommendations: The same design rules as for the previous inverting buck-boost converter can be applied. The output capacitor Cout must be chosen larger than would be required for a what standard buck converter. Low input voltages or high output currents require a large value output capacitor (in the range of thousands of mF). The recommended range of inductor values for the negative boost regulator is the same as for inverting converter design. Another important point is that these negative boost converters cannot provide current limiting load protection in the event of a short in the output so some other means, such as a fuse, may be necessary to provide the load protection. http://onsemi.com 19 LM2594 Delayed Startup There are some applications, like the inverting regulator already mentioned above, which require a higher amount of startup current. In such cases, if the input power source is limited, this delayed startup feature becomes very useful. To provide a time delay between the time when the input voltage is applied and the time when the output voltage comes up, the circuit in Figure 28 can be used. As the input voltage is applied, the capacitor C1 charges up, and the voltage across the resistor R2 falls down. When the voltage on the ON/OFF pin falls below the threshold value 1.3 V, the regulator starts up. Resistor R1 is included to limit the maximum voltage applied to the ON/OFF pin. It reduces the power supply noise sensitivity, and also limits the capacitor C1 discharge current, but its use is not mandatory. When a high 50 Hz or 60 Hz (100 Hz or 120 Hz respectively) ripple voltage exists, a long delay time can cause some problems by coupling the ripple into the ON/OFF pin, the regulator could be switched periodically on and off with the line (or double) frequency. +Vin +Vin 7 LM2594 R2 10 k R3 47 k Cin 100 mF 5 ON/OFF 6 GN D Z1 1N5242B Q1 2N3904 R1 10 k Vth 13 V NOTE: This picture does not show the complete circuit. Figure 29. Undervoltage Lockout Circuit for Buck Converter The following formula is used to obtain the peak inductor current: I (V ) |V |) O ) V in x t on [ Load in peak 2L 1 V in |V | O where t on + x 1.0 , and f osc + 52 kHz. V ) |V | fosc in O I +Vin +Vin 7 C1 0.1 mF 5 LM2594 ON/OFF 6 Cin 100 mF GN D R1 47 k Under normal continuous inductor current operating conditions, the worst case occurs when Vin is minimal. R2 47 k +Vin +Vin 7 LM2594 NOTE: This picture does not show the complete circuit. Figure 28. Delayed Startup Circuitry Undervoltage Lockout R2 15 k R3 47 k Cin 100 mF 5 ON/OFF 6 GN D Some applications require the regulator to remain off until the input voltage reaches a certain threshold level. Figure 29 shows an undervoltage lockout circuit applied to a buck regulator. A version of this circuit for buck-boost converter is shown in Figure 30. Resistor R3 pulls the ON/OFF pin high and keeps the regulator off until the input voltage reaches a predetermined threshold level with respect to the ground Pin 3, which is determined by the following expression: (Q1) V [ V ) 1.0 ) R2 V th Z1 R1 BE Z1 1N5242B Q1 2N3904 R1 15 k Vth 13 V Vout NOTE: This picture does not show the complete circuit. Figure 30. Undervoltage Lockout Circuit for Buck-Boost Converter Adjustable Output, Low-Ripple Power Supply A 0.5 A output current capability power supply that features an adjustable output voltage is shown in Figure 31. This regulator delivers 0.5 A into 1.2 V to 35 V output. The input voltage ranges from roughly 3.0 V to 40 V. In order to achieve a 10 or more times reduction of output ripple, an additional L-C filter is included in this circuit. http://onsemi.com 20 LM2594 40 V Max Unregulated DC Input Feedback +Vin 7 Cin 100 mF 6 4 LM2594 Output GND 5 8 ON/OFF D1 1N5822 Cout 220 mF L1 100 mH CFF R2 50 k C1 100 mF L2 3 mH Output Voltage 2 to 35 V @ 0.5 A R1 1.21 k Optional Output Ripple Filter Figure 31. 2 to 35 V Adjustable 0.5 A Power Supply with Low Output Ripple http://onsemi.com 21 LM2594 THE LM2594 STEP-DOWN VOLTAGE REGULATOR WITH 5.0 V @ 0.5 A OUTPUT POWER CAPABILITY. TYPICAL APPLICATION WITH THROUGH-HOLE PC BOARD LAYOUT 4 Unregulated DC Input +Vin = 10 V to 40 V +Vin 7 6 C1 100 mF /50 V ON/OFF GND 5 Feedback LM2594 Output 8 ON/OFF L1 100 mH R2 3.0 k C2 220 mF /25 V CFF Regulated Output Filtered Vout2 = 5.0 V @ 0.5 A D1 1N5819 R1 1.0 k V C1 C2 D1 L1 R1 R2 - - - - - - 100 mF, 50 V, Aluminium Electrolytic 220 mF, 25 V, Aluminium Electrolytic 1.0 A, 40 V, Schottky Rectifier, 1N5819 100 mH, DO3340P, Coilcraft 1.0 kW, 0.25 W 3.0 kW, 0.25 W R2 out + V ref ) 1.0 ) R1 Vref = 1.23 V R1 is between 1.0 k and 5.0 k Figure 32. Schematic Diagram of the 5.0 V @ 0.5 A Step-Down Converter Using the LM2594-ADJ NOTE: Not to scale. NOTE: Not to scale. Figure 33. Printed Circuit Board Layout With Component References Figure 34. Printed Circuit Board Layout Copper Side * * * * National Semiconductor LM2594 Data Sheet and Application Note National Semiconductor LM2595 Data Sheet and Application Note Marty Brown "Practical Switching Power Supply Design", Academic Press, Inc., San Diego 1990 Ray Ridley "High Frequency Magnetics Design", Ridley Engineering, Inc. 1995 http://onsemi.com 22 LM2594 ORDERING INFORMATION Device LM2594DADJG LM2594DADJR2G LM2594PADJG Device Marking LM2594 LM2594 2594-ADJ Package SOIC-8 (Pb Free) SOIC-8 (Pb Free) PDIP-8 (Pb Free) Shipping 98 Units / Rail 2500 / Tape & Reel 50 Units / Rail For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 23 LM2594 PACKAGE DIMENSIONS SOIC-8 NB CASE 751-07 ISSUE AJ -X- A 8 5 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. 751-01 THRU 751-06 ARE OBSOLETE. NEW STANDARD IS 751-07. DIM A B C D G H J K M N S MILLIMETERS MIN MAX 4.80 5.00 3.80 4.00 1.35 1.75 0.33 0.51 1.27 BSC 0.10 0.25 0.19 0.25 0.40 1.27 0_ 8_ 0.25 0.50 5.80 6.20 INCHES MIN MAX 0.189 0.197 0.150 0.157 0.053 0.069 0.013 0.020 0.050 BSC 0.004 0.010 0.007 0.010 0.016 0.050 0_ 8_ 0.010 0.020 0.228 0.244 B 1 S 4 0.25 (0.010) M Y M -Y- G K C -Z- H D 0.25 (0.010) M SEATING PLANE N X 45 _ 0.10 (0.004) M J ZY S X S SOLDERING FOOTPRINT* 1.52 0.060 7.0 0.275 4.0 0.155 0.6 0.024 1.270 0.050 SCALE 6:1 mm inches *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 24 LM2594 PACKAGE DIMENSIONS 8 LEAD PDIP CASE 626-05 ISSUE L NOTES: 1. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 2. PACKAGE CONTOUR OPTIONAL (ROUND OR SQUARE CORNERS). 3. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. DIM A B C D F G H J K L M N MILLIMETERS MIN MAX 9.40 10.16 6.10 6.60 3.94 4.45 0.38 0.51 1.02 1.78 2.54 BSC 0.76 1.27 0.20 0.30 2.92 3.43 7.62 BSC --10 _ 0.76 1.01 INCHES MIN MAX 0.370 0.400 0.240 0.260 0.155 0.175 0.015 0.020 0.040 0.070 0.100 BSC 0.030 0.050 0.008 0.012 0.115 0.135 0.300 BSC --10_ 0.030 0.040 8 5 -B- 1 4 F NOTE 2 -A- L C -T- SEATING PLANE J N D K M M TA B H G 0.13 (0.005) M M ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative http://onsemi.com 25 LM2594/D |
Price & Availability of LM2594
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |